The Safety Rail Source Kee Access® ADA safety railing and handrails are a cost effective solution to satisfy ADA, ICC and building code requirements. ADA railing pipe and fittings are shipped as an E-Z install railing kit. Railing fittings slip inside the railing pipe to make a smooth railing system. Railing pipe and fittings can be painted to your desired color. See fittings below to see our ADA railing fittings.
Give us your ADA railing layout or CAD drawing and we'll design your kit including pipe and fittings for E-Z installation. Your system will come complete with pre-cut pipe and ADA compliant fittings. All you need for installation is a hex key and your mounting hardware!
About ADA Handrailings & Railings Requirements & Regulations
Safety Rail Source ADA railings are ideal for new structures or for retrofitting old structures. Existing railings can be updated to be ADA compliment with the addition of the “Add-On” offset fittings A10-748 and A10-848.
The purpose of this part is to implement title III of the Americans with Disabilities Act of 1990 (42 U.S.C. 12181), which prohibits discrimination on the basis of disability by public accommodations and requires places of public accommodation and commercial facilities to be designed, constructed, and altered in compliance with the accessibility standards established by this part.
(a) General. This part applies to any --
(1) Public accommodation;
(2) Commercial facility; or
(3) Private entity that offers examinations or courses related to applications, licensing, certification, or credentialing for secondary or postsecondary education, professional, or trade purposes.
(b) Public accommodations. (1) The requirements of this part applicable to public accommodations are set forth insubparts B, C, and D of this part.
(2) The requirements of subparts B and C of this part obligate a public accommodation only with respect to the operations of a place of public accommodation.
(3) The requirements of subpart D of this part obligate a public accommodation only with respect to --
(i) A facility used as, or designed or constructed for use as, a place of public accommodation; or
(ii) A facility used as, or designed and constructed for use as, a commercial facility.
(c) Commercial facilities. The requirements of this part applicable to commercial facilities are set forth in subpart D of this part.
(d) Examinations and courses. The requirements of this part applicable to private entities that offer examinations or courses as specified in paragraph (a) of this section are set forth in Sec.36.309.
(e) Exemptions and exclusions. This part does not apply to any private club (except to the extent that the facilities of the private club are made available to customers or patrons of a place of public accommodation), or to any religious entity or public entity.
ADA Standards That Apply to Ramps and Handrails
4.8.1* General. Any part of an accessible route with a slope greater than 1:20 shall be considered a ramp and shall comply with 4.8.
4.8.2* Slope and Rise. The least possible slope shall be used for any ramp. The maximum slope of a ramp in new construction shall be 1:12. The maximum rise for any run shall be 30 in (760 mm) (see Fig. 16). Curb ramps and ramps to be constructed on existing sites or in existing buildings or facilities may have slopes and rises as allowed in 4.1.6(3)(a) if space limitations prohibit the use of a 1:12 slope or less.
4.8.3 Clear Width. The minimum clear width of a ramp shall be 36 in (915 mm).
4.8.4* Landings. Ramps shall have level landings at bottom and top of each ramp and each ramp run. Landings shall have the following features:
(1) The landing shall be at least as wide as the ramp run leading to it.
(2) The landing length shall be a minimum of 60 in (1525 mm) clear.
(3) If ramps change direction at landings, the minimum landing size shall be 60 in by 60 in (1525 mm by 1525 mm).
(4) If a doorway is located at a landing, then the area in front of the doorway shall comply with 4.13.6.
4.8.5* Handrails. If a ramp run has a rise greater than 6 in (150 mm) or a horizontal projection greater than 72 in (1830 mm), then it shall have handrails on both sides. Handrails are not required on curb ramps or adjacent to seating in assembly areas. Handrails shall comply with 4.26 and shall have the following features:
(1) Handrails shall be provided along both sides of ramp segments. The inside handrail on switchback or dogleg ramps shall always be continuous.
(2) If handrails are not continuous, they shall extend at least 12 in (305 mm) beyond the top and bottom of the ramp segment and shall be parallel with the floor or ground surface (see Fig. 17).
(3) The clear space between the handrail and the wall shall be 1 - 1/2 in (38 mm).
(4) Gripping surfaces shall be continuous.
(5) Top of handrail gripping surfaces shall be mounted between 34 in and 38 in (865 mm and 965 mm) above ramp surfaces.
(6) Ends of handrails shall be either rounded or returned smoothly to floor, wall, or post.
(7) Handrails shall not rotate within their fittings.
4.8.6 Cross Slope and Surfaces. The cross slope of ramp surfaces shall be no greater than 1:50. Ramp surfaces shall comply with 4.5.
4.8.7 Edge Protection. Ramps and landings with drop-offs shall have curbs, walls, railings, or projecting surfaces that prevent people from slipping off the ramp. Curbs shall be a minimum of 2 in (50 mm) high (see Fig. 17).
4.8.8 Outdoor Conditions. Outdoor ramps and their approaches shall be designed so that water will not accumulate on walking surfaces.